$3.49 Buy It Now or Best Offer
free,30-Day Returns

Seller Store
() %,

Location:
Ships to: US,
Item: 392046169318

Condition:New: A brand-new, unused, unopened, undamaged item (including handmade items). See the seller’s … Read moreabout the conditionNew: A brand-new, unused, unopened, undamaged item (including handmade items). See the seller’s listing for full details. See all condition definitionsopens in a new window or tab
Cox:Cox
MPN:Does Not Apply
Part:Engine/Motor Components
For Vehicle Type:Airplane
Fuel Source:Nitro
UPC:Does Not apply

eBay 4x Cox .074 Queen Bee RC Model Engine Propeller Spinner Screw 074 Satisfaction Guaranteed! This sale is for four (4) .074 Queen Bee Propeller Screws Features: Zinc plated 5-40 x 1.25″ Slot – Round head Brand new Current Production item(s) Application: All Cox .074 Queen Bee Engines STORE CATEGORIES CLEARANCE Engines Diesel Engines Engines with Tanks Engines without Tanks Performance Engines RC Engines 010 Parts 020 Parts 049 /051 Parts Back End Front End Top End 050 Parts 074 Parts 09 Parts 15 Parts Propellers Fuel Tanks/Lines Performance Airplane/Starter Kits Field Gear Tooling Fasteners Backplate Screws Mounting Screws Prop Screws Car & Plane Parts Building Supplies Miscellaneous GUIDES View our guides on your computer on any of our item listings: • Engine Operation Guide • Fuel Guide • Diesel Engine Basics • Engine Troubleshooting Chart • Care & Maintenance Guide STORE CATEGORIES CLEARANCE Engines Diesel Engines Engines with Tanks Engines without Tanks Performance Engines RC Engines 010 Parts 020 Parts 049 /051 Parts Back End Front End Top End 050 Parts 074 Parts 09 Parts 15 Parts Propellers Fuel Tanks/Lines Performance Airplane/Starter Kits Field Gear Tooling Fasteners Backplate Screws Mounting Screws Prop Screws Car & Plane Parts Building Supplies Miscellaneous 4x Cox .074 Queen Bee RC Model Engine Propeller Spinner Screw 074 Satisfaction Guaranteed! This sale is for four (4) .074 Queen Bee Propeller Screws Features: Zinc plated 5-40 x 1.25″ Slot – Round head Brand new Current Production item(s) Application: All Cox .074 Queen Bee Engines Shipping Free shipping on additional items! (Does not apply to some heavy and / or bigger items) Shipping charge is based upon the item with the highest shipping cost. Professional packaging as well as insurance to full merchandise value is included. To get combined shipping please add all items to cart before proceeding to pay. All items will be shipped within one business day of purchase, Returns You may return merchandise for any reason within 30 days! All returns must be unused, complete and in the same condition as shipped. We will refund your purchase price as well as the shipping cost you initially paid us. Reasonable return costs will be refunded if the item is not as described or defective. However, it is important that you contact us beforehand to receive an authorization. Contact We respond promptly to all inquiries! Please contact us through eBay Messages Our office is staffed from 08:00 to 16:00 hrs Pacific Time, Mon – Fri, excluding holidays. No answer to your e-mail within one business day? Please check your spam folder. Engine Operation Guide ENGINE OPERATION GUIDE You will need: Small, external fuel tank (unless your engine has an integrated tank) Fresh, well charged battery (two 1.5 volt •D• cells with terminals soldered •+• to •+• and •-• to •-• or use a battery box) A 1.5v hobby battery would be fine. DO NOT use a battery over 1.5 volts; it will burn out the glow head. Glow head clip A model airplane fuel consisting of 15-25% nitro (35% for racing) and a minimum of 20% oil (at least 1/2 of that 20% has to be Castor oil). A propeller with a diameter of 5•, 5½ • or 6• and a pitch of 3• or 4• Propeller screw & washer 2 Cox Wrenches Optional accessories: Spring starter After-run oil (CoxLube or similar) Starter •chicken• stick or ½A electric starter (Electric starter not recommended / risk of breaking the conrod) Starting your engine: Fill the fuel tank with clean fuel. This is self-explanatory and everyone has their own preferred method. If possible, use an inline fuel filter to keep the fuel clean. Keep all fuel equipment clean! If you are using an engine that requires an external tank, you should make sure there is fuel in the fuel line before trying to start the engine. There are several ways to fill the fuel line. One method is blowing lightly into the tank vent until you see fuel flowing through the fuel line. Turn the needle clockwise until it stops. Do not force it! Then, turn the needle 3 full turns counter-clockwise. Once running, you can lean the mixture by turning the needle clockwise. Squirt a few drops of fuel into either the top of the air intake, the carburetor or into the cylinder exhaust port. Close the opening with your finger and flip the prop over a few times. Use a fresh battery and connect the glow head clip to the top of the glow head (see drawing on page two). It is important that you prime the engine before connecting the glow head clip. Priming with the battery attached can cause the fuel to ignite and the prop to kick, potentially wounding your fingers. Turn the engine over by flipping the propeller. If your engine has a spring starter, simply wind the spring one turn clockwise and release. If your engine doesn’t have a spring starter, simply flicking the prop over vigorously (from right to left when facing the prop) works as well as anything else. If the engine fires but does not start, and there is not an excess of raw fuel flowing out of the exhaust ports, enrich the mixture by turning the needle a quarter turn counter clockwise. Repeat the starting procedure. If the engine runs but slowly bogs down, stopping with amounts of fuel appearing around the ports, the mixture is too rich. Lean it out by turning the needle a quarter turn clockwise. Once the engine is running continuously, remove the glow head clip. Play with the needle to adjust the setting to optimal RPM. Turning the needle counter-clockwise allows more fuel to pass through, and the engine will start to run rough or lumpy. You will see copious amounts of fuel and oil flowing out of the exhaust ports. Turning the needle clockwise will lean out the mixture, causing the RPM to increase. However, the RPM will only increase to a point, after which there is not enough fuel in the relation to air being absorbed; and the engine quits. It is a good Idea to run the engine a bit on the rich side, as this will promote longer engine life. Also, you don’t want to lean out the mixture fully on the ground because, once in the air, the engine tends to lean itself out and may stall if the setting was already very lean on the ground. Turning the needle counter-clockwise ½ turn from full RPM is a good compromise. Connect Cox glow head clip wires to a 1½ volt battery or Cox battery box. Attach glow head clip to glow head. Starting your engine (cont.): Sometimes (if you don’t have a spring snap starter) the engine may start backwards. You can either wait for the engine to run out of fuel, turn in the needle valve or you can stop it by pinching the fuel line. Reed valve engines can run in either direction (there will be more crankcase and drive-plate wear from excessive “pusher” use). If you have a pusher engine (usually has a brass drive-plate), you shouldn’t have to worry about wear between the crankcase and drive-plate through normal “pusher” use. A brand new engine should be broken in. Simply run the engine for one full fuel tank in a very rich mixture setting. Let the engine cool off and repeat with a slightly leaner mixture (higher RPM). Repeat once more at almost full RPM and you are set to go. Fuel Guide Fuel Guide Cox engines typically run on what is termed “½A fuel”, a fuel with high nitro content and containing some castor oil instead of synthetic oil only. This fuel mixture is becoming increasingly difficult to obtain. Often, when referring to “½A” in hobby shops, it will elicit blank stares. ½A fuel in loose terms is 15-35% nitro (a.k.a. nitromethane), 20% (castor) oil and the balance methanol (a.k.a. methyl alcohol, carbinol, wood alcohol, wood naphtha or wood spirits). Cox engines will run best on a fuel mix that contains 25% to 35% nitro, whereas the higher nitro content will lead to higher RPM’s but also leads to higher heat and a shortened engine life. The Tee Dee series are better suited to higher nitro content, whereas the basic production engines are best run with a lower nitro content. Operating your Cox engine with less than 15% nitro content might make adjusting the needle valve somewhat quirky. The biggest challenge is finding pre-mixed fuel that contains castor oil, as most fuels sold nowadays contains synthetic oil only, which can lead to premature failure of the engine’s piston ball and socket. There are some “½A” fuels on the market that contain 100% synthetic oil. DO NOT run your Cox engine on such a mixture. Cox recommends a fuel mix containing 20% castor oil. Under strict racing conditions, as little as 5% castor oil (and the balance synthetic) is required to protect the engine for it’s short racing life but is not recommended for recreational flying, where longevity of engine life is desired. To be on the safe side, we recommend at least 10% castor oil and 10% synthetic oil. The upside of using a 50/50 castor/syn mix is that it will help reduce varnishing and leave less oil residue on the model. For Cox engines with diesel conversions, you don’t use actual “diesel” or glow fuel. Instead you use a mix consisting of castor oil, ether and kerosene. A good diesel mix would have 25% castor oil, 40% ether and 35% kerosene (paraffin). How do I obtain pre-mixed ½A fuel? The first place you should check would be your local hobby shop. If they sell ½A fuel, ensure it contains an appropriate amount of castor oil. If they do not, ask for fuel that contains castor oil. To obtain diesel, Diesel Doctor manufactures an excellent diesel fuel and it can be purchased from the manufacturer and other on-line stores. Please see the chart contained in this guide for a list of suggested fuel brands and where to get them. If you cannot find fuel with castor oil, you can add your own! Simply purchase a good fuel with 25-35% nitro and low oil content. Purchase castor oil separately and add to fuel. It is recommended that you use a fuel chart or do the math to figure out how much castor oil to add to fuel. A Castor Oil Calculator is available @ www.coxengines.com/files/castor.xls (must have MS Excel 2003 or later to open / use it). Can I mix my own fuel? Absolutely! Many modelers mix their own fuel. Mixing your own fuel allows you to make a custom mix for your application. Mixing fuel is quite simple and easy although finding some of the ingredients may not be as much fun. A “Google” search is likely a good place to start your search for the proper ingredients. Methanol can usually be obtained from outfits that supply fuel for race cars, or from chemical supply houses. Castor oil is available at off-road motorcycle shops, at grocery stores, pharmacies, etc. You will only require industrial grade castor oil and there is no need to purchase the more expensive medical-grade version. Klotz BeNol is a good choice and is available at motorcycle shops as well as online. Nitro is somewhat controlled and fairly difficult to purchase. Your best bet, again, is contacting outfits that supply fuel for automobile/boat racing or chemical supply companies. Ether in itself is a bit difficult to purchase, just like nitro. Try a chemical supply house. More expensive but an acceptable replacement, is starter fluid, such as John Deere. Kerosene is quite easily obtained at sporting goods stores, in their camping section. Use the unscented variety. NoBrand Website Country Available Order On-line Add Castor Oil Brodak 25% & 35% Nitro www.brodak.com USA Yes No Sig Champion 25 www.sigmfg.com Worldwide Yes No Ritch’s Brew www.ritchsbrew.com USA Yes No Fitz Fuels www.fitzfuels.com USA Yes No Doctor Diesel (Diesel engines) www.cafes.net/doctordiesel USA Yes No Diesel Engine Basics DIESEL ENGINE BASICS (This diesel engine guide is brought to you by Ian McQueen) A model diesel engine is a “compression ignition” engine, physically the same as a glow two-stroke engine apart from the design of the cylinder head, and we’ll get to that part later. One of the facts of physics is that if a gas is compressed quickly, its temperature rises. If the compression ratio is high enough and the compression rapid enough that very little heat is lost from the gas, the temperature achieved is high enough to ignite an air-ether mixture. This ether (di-ethyl ether, once used as an anaesthetic) is a critical component of model diesel fuel because of its low ignition temperature. Typically it makes up 32% or more of the mixture. The main power ingredient is kerosene (or jet fuel, which is more highly refined). It has more energy per unit volume than ether. The ether is required to ignite it. The rest of the fuel is lubricant, usually castor oil. It is much better if there is also 1.5 – 2% of an ignition improver like the amyl/hexyl/octyl/iso-propyl nitrate. This makes starting easier, makes the engine run more smoothly, and reduces loads on internal parts by reducing the compression ratio required to run the engine. Those are the fundamentals, but they don’t begin to explain the advantages of a diesel engine. I consider the biggest feature of a diesel to be its great flexibility, its ability to turn a large variety of propellers. Why this is important leads first to a discussion of propellers. Propellers A given engine can drive a propeller of large diameter and low pitch or one of small diameter and high pitch. A large-diameter, low-pitch prop moves a large volume of air at moderate speed and provides high thrust. It is like low gear in a car: lots of pulling power, but not able to move the vehicle very fast. And a small-diameter prop turning at high speed provides a high-speed blast of a relatively small volume of air. It is like high gear: it doesn’t have the thrust to get the car moving from a standstill, but can drive it to high speed once the car is moving. On a racing plane, a large, low-pitch prop would scarcely get the model flying. On a slow-flying model, a small prop turning at very high speed would generate very little thrust and would have difficulty getting the model moving. For a slow-flying model, the optimum large prop will be turning at a relatively leisurely pace, say 6,000 – 11,000 rpm, while the smaller prop of a fast model will be going a zillion rpm. Converted from metric, a zillion might be 11,000 up to more than 30,000 for racing. In any case, the pitch must be high enough to move the plane at the intended speed when it is turning at the speed that the engine is able to turn it. Glow engines are usually designed to develop their power at quite high rpm, say 11,000 to 15,000 rpm or more. They are happiest with relatively low loads, in the form of props with relatively small diameters. If loaded down with a large prop, they may overheat due to pre-ignition. Here’s a brief description of why. In a glow engine, the fuel will begin to burn at a fixed point on the upstroke (with some caveats). With a suitable, relatively small, propeller, this point will be such that the engine fires at just the right time so that the maximum pressure is reached just at TDC. If you put a large prop on that engine, it will still fire at exactly the same point on the upstroke. However, the higher drag of the prop is causing the crankshaft to turn more slowly and prevents the piston from moving as quickly. The result is that maximum pressure will be reached before the piston reaches TDC. This is pre-ignition and puts a strain on all moving parts of the engine: the piston crown, piston pin, con rod, and crankpin. It can often be heard as a pinging or cackling, and the effect is that the engine will overheat. It can be seriously damaged. (Note that the fuel in a properly-operating engine “burns” very rapidly, but it is still burning. It does not “explode” or “detonate”. Those words describe undesirable pre-ignition.) A diesel, on the other hand, can turn the ordinary props used on glow engines at very respectable speeds, but it can also swing larger props because the ignition timing can be varied so that the fuel begins burning at just the right point on the upstroke, just as the spark is timed precisely in an automotive engine. How is this done? A model diesel has a screw of some kind in the head. (There are a few exceptions, but they’re not important.) It pushes against a contra-piston, a movable “plug” inside the top of the cylinder that forms the top of the combustion chamber. Pushing the contra-piston down with the screw decreases the volume and thus increases the CR, so the point on the piston upstroke where the required temperature is produced is lowered. This advances the timing. Conversely, turning the screw out allows the contra-piston to be pushed farther up the cylinder when the piston rises and the trapped gas presses against the bottom of the contra-piston. (Sometimes it sticks, but that’s one of the things that make diesels so interesting!) Raising the contra-piston lowers the CR and retards the timing so that a larger prop can be driven with no risk to the engine. To show the effectiveness of this control, the people at PAW once put a huge 18-6 prop on a PAW 35 engine and started it. It could turn only 3500 rpm, but it ran for five hours straight with no damage to the engine! The test was stopped just because the people wanted to go home. To vary the ignition point of a glow engine it is necessary to try different glow plugs, install or remove head shims to reduce or raise the compression ratio (in effect, a glow-engine is a glow-assisted diesel!), and play around with the percentage of nitromethane in the fuel. Compare this with merely turning the compression-adjusting screw of the diesel engine. Other advantages: In addition to the greater flexibility of a diesel engine vis-à-vis glow, a diesel offers the following other advantages: lower noise level more pleasing, more “masculine” sound quality longer running time on the same volume of fuel no need to buy glow plugs or batteries a certain aroma that is guaranteed to identify the modeller as a real “diesel man” STARTING AND ADJUSTING FUEL The fuel consists of kerosene for power, ether to ignite the kerosene, lubricant, and an ignition improver. Here are some notes about the ingredients. Lubricant There have been many fuel formulas, with oil content ranging from 12% (for racing in ABC engines) to 33% (old “British” formula). Recently I saw up to 40% for breaking in the MP Jet engine, but that seems really high! In the typical diesel, with an iron (Meehanite) piston and hardened steel cylinder, the minimum oil content recommended is 23%. It’s a characteristic for proper lubrication of those two materials. A safe bet is 25% oil for any engine. That way there’s lots of lubrication for the connecting rod. PAW recommends 30% for break-in, and it isn’t going to do any harm to run higher oil (over 25%) all the time, but the surplus is going to go out the exhaust and may not contribute much to lubrication beyond 25%. “Oil” is taken to mean castor oil, the best lubricant for model engines.? There is greater force on the con rod bearings of a diesel than of a glow engine, so the insurance of the castor oil is well worth the added mess from the exhaust spray. Ether Typical ether content is 32%. This assures good atomization, and also gives a safety margin for loss due to evaporation, for the ether will evaporate quickly if the container is left unsealed (especially when the air is hot). Engines will run on lower percentages; apparently 25% is no problem, and probably one can go lower yet. But at some point the fuel will not atomize as finely and power can be expected to drop. There might also be some effect on combustion, and possibly it would be necessary to increase the compression to get the fuel to ignite early enough on the upstroke. This is not a good idea, for it will impose heavier loads on the moving parts. Some fuels are even higher than 32% in ether. They will burn cooler than “standard” fuel and will produce less power, but there may be some times when this is an advantage, as with a Cox International head for a Cox engine; the lower temperature is not as likely to melt the Teflon disc that seals the top of the cylinder. This disc melts when “normal” fuel is used and the engine is tuned for full power. It is my understanding that fuel for the Cox International-converted Cox engines should have about 40% ether. Higher ether content can apparently be used if an ignition improver chemical is not available, but I have no real information on this. Ether used to be easy to obtain when it was still being used as an anaesthetic. But it is not used for that purpose any more, so there is little incentive for drug stores to carry it. And ether is also used in processing some illegal drugs, which has made it difficult for legitimate users to obtain it. Starting spray for full-size engines contains ether. One source is John Deere dealers. One freezes the container and punctures it to release the ether, but I have never done this, and these instructions are not enough to teach you how to do it safely! Ignition improver The ignition improver, like Ethyl’s DII(3) (octyl nitrate), causes the ether to ignite at a lower compression ratio, and also smoothes the combustion process. Without it, a diesel has a cackly, rattly sound, and compression has to be set higher, which puts more load on the moving parts. With it, a diesel runs smoothly and purrs like a tiger. A typical formulation is 2% for engines up to about .19 and 1.5% for larger engines.? Kerosene Kerosene or jet fuel makes up the balance. Kerosene has higher energy per volume than ether, so a higher percentage of kerosene is desirable. But this is limited by considerations of ignition and lubrication. Commercial fuel The simplest way for most modellers to obtain diesel fuel is to obtain it from one of the commercial manufacturers/suppliers. Companies that I know of that sell diesel fuel in the USA are: Eric Clutton (Dr. Diesel) Aerodyne Red Max Ed Carlson Davis Diesel OPERATION The following instructions begin with starting a diesel engine, then branch to adjusting it for full power output (for a broken-in engine) and for break-in (for a new engine). STARTING THE ENGINE Probably the most difficult part of running a diesel engine is getting it to fire the first time. This may not seem like a particularly profound statement, but they do have to be set within a small range of adjustments to fire properly. One would think that it is only necessary to crank the compression high and it should fire. But it doesn’t work that way. The engine can be just as reluctant to start if the compression is too high as it is if the compression is too low, maybe even more so. The following method of starting a diesel is my own, which I immodestly call the “McQueen Method” since I have never seen the key part described anywhere else. The key part? Whereas other starting instructions always seem to include the words “Fill the tank” at the beginning, I emphatically say “Do not fill the tank!!” Determine the correct starting settings by running the engine only on a prime. Then fill the tank, get the engine to run continuously, and adjust it for full power.? Why this way? The reason is because a diesel is easy to flood, and a flooded diesel is very difficult to start. The idea is to put a controlled amount of fuel into the engine and to start the engine on that. But if there is fuel in the tank, it is very likely to dribble into the engine and interfere with your efforts to put in that right amount of fuel. Note that there are ways around the problem of flooding if it occurs, and I’ll include them below, but they require a lot of unscientific fiddling and tomfoolery that can be avoided if you follow these instructions carefully and understand why you are doing what you are doing. (Much of the information here can be usefully adopted for starting glow engines.). The most important single instruction is: DO NOT FLOOD THE ENGINE! PREPARATIONS Mounting the engine Mount the engine on a strong mount (or in a model). It is convenient if the engine can be removed from a mount without too much difficulty in case it is necessary to invert it and drain out excess fuel, though this will not be a problem if you are careful and don’t flood it. And excess fuel can be cleared if you just flip the prop long enough. (Reduce the compression initially to reduce load on the innards.) Do not mount the engine inverted. Fuel system The fuel tank should be positioned as with any model engine, as close as possible to the engine and with the center line of the tank no higher than the spraybar. (Some sources say to put the top of the tank level with the spraybar. Partly this depends on the ability of the engine to draw fuel.) And, as touched on above, keep the spraybar higher than the tank (or the supply line pinched off) when the engine is not running, to keep fuel from dribbling into the engine. For flexible fuel line, use only neoprene. Silicone tubing should not be used because it swells up in contact with diesel fuel, though you should get by using it for a day if you are prepared to replace the tubing. Ordinary PVC (vinyl) tubing can be used where flexibility is not needed. It will become stiff after prolonged contact with fuel. Propeller Select a prop of suitable size from the engine manufacturer’s instructions. For break-in, a “suitable size” is one of greater length and lower pitch within the mid-range of sizes suggested in the instructions (so that it will not place a heavy load on the engine). And, the heavier the prop – such as nylon, the better for greater flywheel action. Mount the prop so that the piston comes up against compression at the “ten past eight” position Compression setting The screw in the head, and thus the position of the contra-piston, are usually in the right ballpark when the manufacturer packages the engine. You did resist the temptation to turn that little screw, didn’t you? PAW test runs every engine to make sure that it will start. Other manufacturers might, also. If it has been moved from the initial position, try to remember where the screw was and return it to that position. Grasp the prop and try turning the engine over. The engine should turn over freely, though compression should be good. If it feels difficult to turn over TDC, compression may be too high. Back the compression screw out at least a quarter turn (it can be more if “little fingers” have been playing with the comp screw) and flip the prop. This should push the contra-piston up, and the resistance due to compression should be reduced. If the engine turns over freely, it should be in the ballpark. If the engine turns over very easily, it is possible that the compression has been set too low. It is just as well to do nothing at this point, but keep in mind that it may be necessary to increase the compression later. As noted earlier, starting is not easier when compression is too high. It seems to make the engine actually harder to start. Often the engine may be under-compressed but a really hard flip will get it to fire anyway. It won’t run properly, but it will still show some life. These uncertainties are what make diesels so much fun! Throttle setting Set the carb wide open. Priming Obtain a small squeeze bottle that you can fill with fuel and then use to measure out fuel drop-by-drop. This ability to measure drops accurately is very important to avoid flooding. I always prime an engine through the venturi or carburetor, not into the cylinder. Some modellers are successful with prime against the side of the raised piston. But if there’s a muffler this becomes impossible anyway. Note that putting even a small amount of fuel into the cylinder decreases the volume, thereby raising the compression ratio. If the CR is just right with the prime, what happens when the fuel burns? The volume decreases, so does the CR, and the engine will likely stop. Or, if the CR is just right for running, the extra volume of fuel may be enough to raise the CR beyond the point where the engine will fire. A prime into the intake allows the fuel to be vaporized and carried into the cylinder in the same way as when the engine is running normally. A correct prime is literally only a couple of drops. Literally! For small engines, .06 and smaller, it should be a single drop, or even a partial drop into the venturi. (Make a drip on the end of the tube and then touch it to the venturi to make it drop into the intake.) For one over, say, .19, it could be two drops and maybe three for a big engine. But don’t go over two drops at first. That should be enough to get the engine to fire and run briefly. Putting the right, small, amount of fuel into the engine is the single most important part of getting your engine running! STARTING THE ENGINE Prime the engine as just described. Hold the prop in your hand and turn the engine over slowly. This is to ensure that the engine is turning freely and that the dreaded hydraulic lock has not occurred. Bring the prop up against compression and then flip it as hard and as quickly as you can. A sharp snap is the key to good starting. If you are really lucky, the engine will start and run for about a second with a good burst of power. This is the optimum response and your target with this exercise. My engines usually do not fire until the second or third flip, so don’t be discouraged if you are not successful on the first flip. Repeat the hard flip, several times if necessary. The following responses are possible: If the engine starts with a good burst of power, perfect. The compression setting is good. If the engine starts, but runs weakly with a “soft” sound and/or misfires (skipping), and soon dies, it is under-compressed. Turn the comp screw in a small amount, about 1/16 of a turn, and flip again a few times without re-priming in case there is still fuel left in the crankcase. If the engine does not fire, prime and try again. Repeat these steps as necessary until there is that good burst of power, and then repeat once to make sure that the action is repeatable. (A slight complication is that running the engine several times will warm it up a little, and that has the same effect as increasing the CR a small amount.) If the engine starts, but runs with a harsh, metallic, rattly, or clattery sound, and stops abruptly, it is over-compressed. Turn the comp screw out 1/8 – 1/4 turn and flip again a few times to push up the contra-piston and to clear out any fuel. It may start while you are doing this. If not, re-prime and try again. Repeat these actions until the engine fires and runs reliably with a good burst of power; then proceed to “RUNNING AND ADJUSTING THE ENGINE”. Flooding If the engine does not start after several tries of these instructions, it may be flooded. Full instructions for clearing a flooded engine are given at the end. Clearing a flooded engine is a general pain, and the fiddling necessary to clear it can get aggravating. Try to avoid flooding it. RUNNING AND ADJUSTING THE ENGINE At this point the engine has run out the prime with a good burst of power. Make a note of the position of the comp screw. (I make a scratch on the head to match a mark or feature on the screw.) That position is your starting point (unavoidable pun) in future for a prop of that size. In colder weather, you may have to turn the screw in slightly from that point; likewise, if you later fit a prop of less diameter and/or pitch (reduced load). And you may have to back the screw out slightly in hot weather or if you fit a prop of larger diameter and/or pitch (increased load). At this point you are ready to run the engine. Needle valve and throttle positions Needle valve: The instructions with the engine should give an indication of a suitable starting position for the needle valve. For an unfamiliar engine being run for the first time, especially for break-in, I usually open the needle valve three to five turns from fully closed. An alternative method used by diesel expert David Larkin is to start with the needle valve open only about half a turn and to open it a quarter turn with each unsuccessful attempt to keep the engine running, but the engine might then run at quite high speed when it catches, and this can be undesirable for an un-run engine.) Throttle: The throttle should be wide open. (With experience you can start at reduced settings; for engines converted from glow with a Cox International head, set the throttle about half-open.) Filling the tank Fill the tank. Be sure that your fuel is fresh. If too much ether has evaporated from the fuel, you will be wasting your time! While filling the tank, clamp off or disconnect the fuel line to the engine so that no fuel can leak into the engine. And, when starting the engine, either pinch off the fuel line with a finger or hold the nose of the model high (if it’s a small-enough model) so that gravity will keep fuel from leaking into the engine. When the engine fires, release the line or return the nose to horizontal. The engine should run long enough on the prime to draw in fuel and keep running. Usually there is no need to draw fuel up to the spraybar beforehand. Fuel will usually be drawn to the engine when it starts. Starting the engine With the fuel line pinched against the engine or model with a finger (or the nose held high), prime the engine and flip it the same way that you did successfully above. As soon as the engine fires, remove your finger from the fuel line (or bring the nose to or below the horizontal). Fuel will usually be drawn to the engine and the engine will keep running. If the engine doesn’t keep running, immediately clamp the fuel line (or lift the nose), open the needle valve 1/4 to 1/2 turn and repeat. When you get the engine to keep running, congratulations! You are well on the way now! And if you are using the method of opening the needle valve in steps from closed and if the engine doesn’t keep running after the prop has been flipped several times, immediately clamp the fuel line (or lift the nose), open the needle valve 1/4 to 1/2 turn, prime, and flip again. Repeat as necessary. Adjusting the engine At this point the engine is running and needs to be adjusted. Instructions are given first for starting and setting an engine that has already been broken in. Instructions for a new engine are given later. The compression screw and needle valve settings interact with each other. The main adjustment is the compression screw. But when the CR has been set properly, the next step may be to lean the fuel mixture more. That will make the engine run hotter, which advances the ignition point, and that in turn may require reducing the CR to retard timing slightly. The following should enable you to adjust the right one at the right time and get the engine adjusted correctly. This may seem daunting the first time, but it becomes instinctive quickly when you understand why you are making an adjustment. I’d like to be able to post a flowchart at this point, for it simplifies the rest of the instructions. But I can’t, so just follow the words. Let the engine run for half a minute to warm up, then go through the following questions and actions. Is it running softly, misfiring, skipping, loping, etc? If so, CR is too low. Turn the comp screw in 1/8 turn.? Alternatively: Is it running harshly, sounding laboured, rattly, cackly? If so, turn the comp screw out 1/8 turn. Repeat these evaluations and adjustments until the engine is running smoothly then continue to adjusting the needle valve. Note: We got to this point by gradually adjusting the needle valve until the engine would keep running, so it should be in the ballpark of the correct setting. Is the engine exhaust very oily? Is the engine four-stroking? If so, it is running too rich. Close the needle valve 1/8 to 1/4 turn, allow a few seconds for the change to take effect, and check again. Repeat this check until the engine is “singing” at a good speed. When the engine is tuned for nearly full power, it will heat up and this advances the ignition. Has the engine sound become laboured, harsh, rattly, or cackly? If so, reduce the CR 1/8 to 1/4 turn and check the sound again. Continue to close the needle valve in small steps. If the engine speeds up, you are going in the right direction. Repeat the procedure. If it begins to misfire, it is probably too lean. Open the needle valve enough to restore smooth operation. If misfiring occurs, the compression may be set too low. Turn the comp screw in 1/8 to 1/4 turn. If the engine speeds up, you are going in the right direction. If the engine sound becomes laboured and harsh, back the comp screw out to the former setting or even beyond. This procedure will have you close to the full power output. If the engine is in a model, try flying it. NOTES: Once the model is released and it accelerates, it is possible that the engine will start to misfire, especially if the engine is fitted with a large, high-load prop. Do not try to fly if it is misfiring. It may not be developing enough power. The needle valve may be too lean, and probably the CR is a little bit too low. (As the plane moves forward, the load on the prop is reduced and the engine can turn faster, needing more fuel. And the ignition point may need to be advanced a little.) Turn the comp screw in about 1/16 turn and open the needle valve a little. Try again. Repeat the adjustments as required. In general it will probably be necessary to richen the mixture slightly and increase the compression slightly from the initial settings to develop maximum power in the air. Miscellaneous notes You do not have to worry about a lean setting damaging a diesel the way it would a glow engine. If a diesel is set too lean it will misfire or simply stop. Once you have become familiar with your engine, particularly if it is .19 or larger, you may be able to prime the engine by choking the inlet and turning the prop enough to draw fuel to the inlet. But this can be tricky, for there is the risk of flooding, especially for small engines. Diesels run cool and the exhaust is much cooler than glow-engine exhaust. You can put a piece of ordinary PVC tubing on the outlet of the muffler to guide exhaust away from the model. The tubing can be up to a foot (30 cm) long without detriment to engine operation. Except when the engine is running very rich, the exhaust has a color. With a light load, the exhaust will be a light tan. But the more heavily it is loaded with a large prop, the more the exhaust will tend toward black. Hence the usefulness of the tubing to keep exhaust oil off the model. (Minimize the amount of this exhaust that gets onto your clothes, for it has a distinctive aroma that not everyone appreciates! Especially wives.) BREAK-IN The instructions with your engine will probably cover this, but here are a few tips anyway. Iron-steel engine: The procedure is to run the engine for a couple of minutes, stop it and let it cool, then run it again. The engine is initially run in a very rich four-stroke, with just enough compression to keep it running smoothly. I build up about 20 minutes at the richest setting, then close the needle valve 1/4 turn for each successive run until the engine is beginning to break into two-stroking. I give it short bursts of moderate-speed two-stroking, again with just enough compression for smooth running, followed by richening it again to keep the engine from running hot too soon. This two-stroking is gradually increased in duration and maximum speed. When the engine (any engine) is manufactured, the surfaces of the piston and cylinder are like microscopic mountains facing each other. The slow break-in allows removing the tips of the peaks an atom or two at a time instead of gouging out chunks of metal. The finished product is a pair of smoothly polished surfaces to run against each other. The reason for slow running and not letting the engine run hot at first is to prevent metal expansion that would push the peaks into hard contact with each other so they break. ABC engine: The procedure is completely different for ABC engines. The principle here is to get the engine reasonably hot as quickly as possible, for the fit between cylinder and piston is usually very tight at TDC and one wants to expand the top of the cylinder enough to provide the normal running clearance. One should use a relatively small propeller so the engine can turn freely and quickly find optimal CR and needle valve settings to run relatively rich at high speed. (K&B, in their instructions for breaking in a glow 6.5RIRE ABC pylon engine recommended a prop cut down so the engine would four-stroke at…..20,000 rpm! Use this information for guidance.) TROUBLESHOOTING Clearing flooding You will flood an engine at some time. Here are some tips on clearing it. They are based on an engine in a model so it can be inverted easily. If the engine is in a test stand, there are ways to clear flooding, but removing the engine for draining remains an option. Block the fuel line. Invert the engine and drain fuel out of the intake and the exhaust. Rock the prop back and forth several times to ensure that the ports open. Turn the engine upright, back off the comp screw 1/2 to 1 full turn. Hold the prop with your hand and turn it over against compression. If it turns easily, continue. However, if there is resistance, keep backing off the screw until it will turn freely. Begin flipping the prop. The engine may start at some time. This will either clear out all the fuel and the engine will run and then come to a soft stop. Or it could draw up a slug of liquid fuel if the engine was really badly flooded. In this case the engine could stop abruptly. If this happens, drain out any fuel possible, reduce the compression more, and flip again. Eventually the excess fuel will be cleared out, compression will again feel soft, and you will need to increase the compression a little at a time. When the engine is somewhere around the normal starting setting, follow the starting procedure from the beginning. This business of clearing a flooded engine is a general pain, and the fiddling necessary to clear it can get aggravating. If you are careful not to flood the engine you should be able to avoid this monkey-foolery completely. But some time your engine is going to get flooded and you have to know how to clear the problem. Poor compression The engine must have good compression if it is to start easily. There are ways around poor compression, and I have had to use them with several engines converted to diesel operation. This is not a reflection on the heads, but on the engines. My problems came with one O.S. 25FSR and all three of my 10FSR engines. All of the 10FSRs had poor compression from new, as did a replacement piston-sleeve set that I put into a 25 engine worn by fine dust at our flying field. I don’t know if O.S. was making them so loose that users could not seize them up with lean runs as glow engines, but the 10s were so loose that they were very difficult to start even as glow engines. If your engine has poor compression, it is better to repair it (new internal parts). However, there are ways around the problem. If you have an electric starter, you can try using it, but very carefully. If the CR is too high, or if hydraulic lock occurs, you can quickly bend a con rod. Be sure that the CR is a little on the low side, and be sure that there is no fuel in the engine (not flooded). Set the throttle to the maximum and the needle valve out enough turns for running. Then apply the starter to the prop, as lightly as possible so the rubber cone can slip if the engine resists turning over. If the engine does not turn over easily, stop immediately and reduce the CR. Also check for excessive fuel inside the engine. I could always start the 10FSRs quickly with a starter. If you don’t have a starter, set the CR and needle valve to approximately the running settings. But this time you have to get just enough liquid fuel into the crankcase that you can invert the engine and have liquid drain around the piston and seal it. Then turn it right-side-up and immediately begin flipping. (Don’t use a starter this time!) With luck the fuel will give enough compression seal to get it going. Sometimes I have had to do the flipping inverted and then right the model when the engine fired, but this was with small models that I could hold in one hand. If you have a new engine you should never need to use these emergency methods. Engine Troubleshooting Chart Engine Troubleshooting Chart Connect Cox glow head clip wires to a 1½ volt battery or Cox battery box (A). Attach glow head clip to glow head (B). TROUBLE PROBABLE CAUSE REMEDY WILL NOT START ACTS LIKE BATTERY WASN’T ATTACHED TO GLOW HEAD Poor battery connection Check connections of wires to battery and check to be sure clip is firmly and correctly attached to glow head. (see glow head clip info above) Weak or dead battery A good battery should test 1½ volts or connect battery to a glow head that is known to be good. If filament does not glow bright orange – replace battery. Burned out glow head Remove glow head. Attach glow head to a good 1½ volt battery. If filament does not glow bright orange – replace head. Engine wasn’t primed Squirt a few drops of fuel through exhaust port and into side of piston then continue starting procedure. WILL NOT START ENGINE POPS AND / OR “KICKS” Loose propeller screw Tighten propeller screw. Dirt under reed (reed valve engines only) Carefully remove reed retainer and then remove reed. Wash reed and retainer in solvent or fresh fuel. Replace reed, be sure it turns freely. ENGINE STIFF PROPELLER TURNS HARD / “KICKS” Engine flooded Too much fuel in cylinder Close needle valve completely. Leave battery attached and flip propeller (without priming) until short starting “burst” occurs. Then open needle valve 2½ (or suggested amount of turns for your engine) and start again. ENGINE STARTS THEN SLOWS DOWN AND STOPS Excess fuel at ports Close needle valve. Flip propeller until engine starts and burns out excess fuel. Open needle valve and restart. SHORT RUNNING “BURST” (BRIEF START, THEN STOPS) Engine not getting enough fuel Mixture too lean or tank empty Carburetor body cracked (Tee Dee & Medallion engines) Check tank fuel level and refill if necessary. Or, open needle valve another ½ turn, prime and start again. It may be necessary to repeat the procedure 3 or 4 times, opening the needle valve ½ turn each time. (Replace carburetor body) ROUGH SOUNDING ENGINE, SLUGGISH, WEAK POWER Loose glow head Tighten glow head with Cox wrench. Mixture too rich Slowly close needle valve until maximum RPM is achieved. Then open needle valve ¼ to ½ turns. Not enough compression With no battery attached, flip prop. If no definite “pop” is heard – replace cylinder/piston assembly. Not enough Nitro in fuel One should use 25% nitro fuel although 15% will produce satisfactory results. Propeller too large Ensure correct prop size for engine. ENGINE RUNS WELL BUT THEN STOPS Mixture too lean Open needle valve ¼ turn or more. RUNS ERRATICALLY Missing or damaged venturi gasket (reed engines with integral tank only) Replace venturi gasket. Bent or broken needle valve Replace needle valve. RUNS WELL BUT NOT LONG ENOUGH (ENGINES WITH INTEGRAL TANKS) Missing fuel pickup tube (inside tank) Install fuel pickup tube (with spring). Pickup tube in wrong position. Reposition fuel pickup tube to “CL” position (8 o’clock) or to “FF”,”RC” position (6 o’clock). Care & Maintenance Guide Care & Maintenance Guide Sooner or later, your engine will need some care and maintenance. Whether you use your engine every day or you just took it out of the box for its first run, you will have to apply the proper care and maintenance to keep it in its best condition. We recommend you read the entire guide for tips and useful information. Recommended Supplies: Two Cox Wrenches CoxLube (or other high-end oil) Bottle of 91% Isopropyl Alcohol (or fresh glow fuel) Several Ziploc bags (or equivalent sandwich bags) Jar (or other closeable container) Small flathead screwdriver Small Phillips head screwdriver Roll of paper towels Before starting: If you are starting a brand new engine that has never been used before, make sure you have read through the original engine manual or the generic Engine Operation Guide available from Cox International (www.coxengines.ca) if you do not have the original engine manual. From Cox International is also available a Fuel Guide as well as a Troubleshooting Chart. If the engine has been boxed up and unused for a decade or longer, there is a good chance the oil applied at the factory has dried or gummed up. Just place a few drops of fresh fuel in the exhaust port and flip the engine over several times. Make sure you mount the engine on your model, wood board or other secure test stand. Never hold the engine in your hand or in a vise. Install a propeller of appropriate size; a prop ranging in the size of 5×3 to 6×4 should work fine for a .049 engine, for instance. Although some Cox engine manuals state that no break in is necessary, we strongly recommend you do so. Follow regular starting procedures according to your manual or the generic Engine Operation Guide but run the engine one full tank on a rich mixture. Let the engine cool off and repeat with a slightly leaner mixture. Repeat once more at almost full RPM and your engine is set and ready to be used! If you are starting a used engine that was not originally yours such as one purchased somewhere or given to you someone else, you won’t exactly know how that engine was cared for. Just because the engine is in cosmetically good condition, doesn’t mean it is in perfect operating condition. That could be the other way around as well; an engine that looks beat up may run like it’s new. Remember, the engine may have been sold by someone who did not know what they had, so expect it to not be exactly as described. Chances are, you didn’t get the original engine manual for your engine. You can either use a manual created for your engine or the Engine Operation Guide from www.coxinternational.ca where you will also find a link to download most original Cox engine manuals. If you are starting an engine that has been stored improperly, such as in the bottom of a dirty toolbox, make sure you carefully disassemble the engine completely and soak it in isopropyl alcohol or fresh fuel for a few hours or overnight. Once you remove it from the solution you soaked it in, use paper towels to wipe all the parts clean. You should not see any specks of dirt on any part of the engine (especially internal parts). Please make note that there is a chance the engine could have some corrosion; corrosion does not wipe off like dirt. A small amount of outer surface corrosion usually doesn’t affect the performance of the engine, but if the engine is heavily corroded or corrosion has formed on the inside of the engine, parts may need to be replaced. If the cylinder appears to have a dark brown deposit or “varnish” on the inside, you will need to use a very fine (000 grade) steel wool to scour the deposit away. Once the engine is clean, reassemble it and you are ready to go. Please make note that you may need to replace the crankcase and venturi gaskets as they may have been damaged while you were taking the engine apart. If the engine is seized or stuck, do not forcefully turn it over! Forcing anything on these engines could cause serious damage to a point where parts will need to be replaced. To free an engine up, try soaking the entire engine in isopropyl alcohol or fresh fuel for a few hours or overnight. If it is still seized, you may have to heat the cylinder and crankcase with a hairdryer. Once hot, you should be able to slowly turn the engine over. If the engine is then still seized and gummed, there are other issues besides dried oil and more action will be needed to free it up. After running your engine After you are done with your engine, steps need to be taken to ensure quick and easy starting the next time you use it. Make sure you run all the fuel out of the tank or empty the tank before storing. After the last run, oil the engine with “CoxLube” (available from www.coxinternational.ca) or other high-end oil. If the engine is removed from the model or test stand, after oiling, wrap the engine in a cloth or paper towel and place it in a plastic Ziploc bag. If the engine is still on the model, wipe the engine down, oil it, wrap it in a cloth or paper towel and then place a plastic Ziploc bag over the engine. If you have had a hard landing where the engine may have gotten dirt in it, remove the engine, take it apart and soak it in isopropyl alcohol or fresh fuel. After a few hours, wipe the engine down and carefully reassemble it. Remember, running a dirty engine could destroy it in just 2-3 minutes! If the engine has made contact with water, take it apart, soak it in isopropyl alcohol or fresh fuel, reassemble and then oil the engine. This is very important especially if the engine has made contact with salt water. Salt water will rust and corrode your engine in a very short amount of time. eBay Store Contact Us Follow Us

Frequently Asked Questions About 4x Cox .074 Queen Bee RC Model Engine Propeller Spinner Screw 074 in My Website

swidnw.com is the best online shopping platform where you can buy 4x Cox .074 Queen Bee RC Model Engine Propeller Spinner Screw 074 from renowned brand(s). swidnw.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling 4x Cox .074 Queen Bee RC Model Engine Propeller Spinner Screw 074 on swidnw.com?

swidnw.com helps you to shop online and delivers Moschino to your doorstep. The best-selling Moschino on swidnw.com are: Moschino MOS020/S Womens Large Metal Sunglass DDB3X Gold Copper w Pink 59-16 Love Moschino Purse Borsa Vit Black Genuine Leather Gold Studded Shoulder Bag Moschino Brown Faux Pearl Eyeglasses *FRAMES ONLY* MO084-04 53-16-135 Italy NWOT Moschino Classic Body Powder With Puff New Moschino Women’s 8 Off White Linen Blend Relaxed Pants MOSCHINO COUTURE! Black Classic Shift Dress – Gold Grommets USA 8 GB 10 Moschino by Moschino, 2.5 oz EDT Spray for Women Women’s Moschino Black Tapered Leg Jersey Knit Pants Size 10 Moschino White X Kelloggs Tony The Tiger Graphic Sweatshirt LOVE MOSCHINO Womens Dress Size 46 Size 10 Python Heart Print Logo Long Sleeve Moschino Cheap And Chic Tweed Style 100% Wool Blazer Jacket UK Size 10 Moschino Cheap & Chic Dress Mixed Print Silk Twill Size US 4 Twist-Front Sheath Moschino Cheap & Chic Black Jacket Size 46 IT Moschino Boutique Tweed Jacket Pink Cropped Pearl Buttons Long Sleeves Size 10 M VINTAGE MOSCHINO RARE ESTATE SALE FIND BLACK CAMEO PATCH PULL ON HI LO SKIRT S/M AW20 Moschino Couture Jeremy Scott Shipping Boxes Packaging Materials Overcoat MOSCHINO LEATHER SKIRT Moschino Jeans Women’s Linen Blazer Size 6 Navy Blue Dark Academia Boutique Moschino stretch High Gather Waist skirt Size IT40 USA6 F36 8 Moschino Cheap Chic Eyelet Wiggle Dress White Cotton Italy Boutique Moschino! -Print Ribbon Dress Size 6US -Very chic! Original Price $525 China Airlines x Moschino Business Class Deluxe Travel Amenity Kit French Blue Moschino Cheap And Chick NWT Dress IT 46 Abstract Print Dolman Sleeve Belted BOUTIQUE MOSCHINO Dress Women Sz 6 RARE Designer Branded Signature Novelty Print Moschino Couture Logo Budweiser printed cotton-jersey joggers pants SZ 10 read Moschino MOS508 C9A 53 Women Eyeglasses Moschino Jeans Women Medium IT 42 Jacket Floral Black Button Long Sleeve Moschino Boutique black jacket coat Sz 6 MOSCHINO FOREVER SAILING FOR MEN EDT SPLASH 20×4.5 ML. MINIATURE (PACK OF 20) MOSCHINO Sunglasses (original Retail Price Was $270.00) MOSCHINO BLACK GRAPHIC PRINT LEATHER CLUTCH RETAIL MADE IN ITALY BNWT MOSCHINO Milano Second Bag Pouch Denim Blue Authentic Used Very Good Item Japan Moschino “I Love 70” Watch New Toy 2 Bubble Gum by 3.4 oz EDT for Women Perfume in Box Moschino This Is Not A Moschino Toy Retro Vintage T-Shirt, S-5XL Moschino Pink Signature Tee T-shirt Rare NEW Moschino Vintage Pebbled Leather Lock Travel Handbag Ivory color Rare 90’s Moschino Dress Apricot Sleeveless Fit Flare Bow Hips Sweetheart Neck Cotton 8 Moschino Lettering Logo Calfskin Women’s Belt in Black with Gold Hardware IT 46 Moschino Women’s 189350 One-Piece Patchwork Animal Print Swimsuit Size 1 Love Moschino Dress Womens 4 Black Sweater Dress Long Sleeves Casual Vintage 80’s Franco Moschino Cheap&Chic RARE Happy Things Shirt 16.5 Men NWOT Moschino Couture by Moschino for Women 1.7 oz Deodorant Parfume Natural Spray L’eau Cheap & Chic by Moschino Eau De Toilette Spray 1.7 oz — Love Moschino Black Yellow Dress Club wear Women’s Dress Size US 2 EU 38 NEW Grey Love Moschino Vest Tank Top With Embroidered Print Size GB 10 Moschino Cheap & Chic Wool Beaded Butterfly Collared Sweater Black Sz 8 vintage cheap and chic Moschino Dress Size 6. MOSCHINO x Disney Top Womens Extra Small Short Sleeve Yellow Tee H&M MOSCHINO Moschino 8-Bit ‘This is not a Moschino Toy’ Bear Logo Tee NEW MOSCHINO MOS128/S MVUIR BLUE AUTHENTIC SUNGLASSES W/CASE 57-14 Love Moschino New Solid Red Sheath Sleeveless Fitted Dress 8 NWOT H&MOSCHINO MOSCHINO H&M JACKET PARKA COAT GOLD SIZE XS Moschino baby girl pink cotton teddy bear logo sweatshirt size 12-18 months, 3 Vintage Moschino Cheap Chic Green Large Bow Shift Mini Dress Sz 8 NEW LOVE MOSCHINO BLACK COTTON LOVE & PEACE EMBROIDERY BLOUSE TOP SHIRT,UK 14 MOSCHINO Jeans Vintage Italy Black/White Check Wool Oversized Shirt Size S Vintage 90s y2k Moschino Mare Dress Slinky Embellished US Size 34 Medium MOSCHINO COUTURE Moschino Couture T-shirt Black ZPA0701 Love Moschino Brown Short Sleeve Shirt size L Cheap and Chic Classic by Moschino Eau De Toilette Spray 1.7oz Love Moschino Men’s Airline Logo Short Sleeve T-Shirt NWT Y2K 2000s Love Moschino Pink Silk Lady Bug Mini Dress drop waist ruffles US 8 LOVE MOSCHINO BASEBALL BLACK PANTS STYLE sz IT 42 US 6 NEW RETAIL $354 MOSCHINO CHEAP AND CHIC BOUCLE DRESS 6 CORAL PINK GOLD BUTTONS BOW FRAN FINE Love Moschino Green Ruffle Draped Long Sleeve Shift Dress Size 10 Love Moschino Womens Sequined Tee Shirt Team Moschino Size 6 NWT MOSCHINO WOMEN’S T SHIRT Yellow Flicker Pink Camouflage Logo (U-002) Moschino Cheap & Chic Vintage Mesh Lavender Embroidered Cami Top | IT 44 | UK 12 MOSCHINO COUTURE BLUE JACKET Trompe L’oeil Blazer USA 4 IT38 $2.4K 2021 RUNWAY Vtg Moschino Jeans Mini Dress Cotton Halter Floral Bow Side Zip Black Small Moschino Olive Oyl Silk Scarf Orchard Heart Cottage Designer Italy Vtg MOSCHINO CHEAP & CHIC 90s DA VINCI OLIVE OYL PRINT BLACK DRESS 42 M Moschino Couture Silk Multicolor Watercolor Abstract Floral Peplum Blazer 42 M Moschino Vintage Faux Leather Jacket PVC Blazer Womens US 8 / It 42 MOSCHINO LOVE DRESS SIZE 10 U.K. RARE Love Moschino Love Logo T-Shirt Black Retro Rainbow HTF Size 8 EUC NWT*MOSCHINO Jeans* shirt-blouse*Size 40 (IT)*RED WINE color*Crystals*VINTAGE Moschino Cheap and Chic Sexy White Draped T Shirt 44/10 Moschino H&M DISNEY Daisy Donald Duck Jumper Sweater Dress S MOSCHINO Women’s Beige Tulip Skirt Asymmetric Pencil Skirt Size 8 / 44 / L MOSCHINO Black Calendar Silk Tie ITALY 56”/ 3.5” EC MOSCHINO mens Shirt Vintage 90s All Over Print Made In Italy 2018 MOSCHINO x H&M Hot Pink Disney Minnie Mouse Merino Wool Sweater Dress – S NWT MOSCHINO HOODIE SWEATSHIRT Teddy bears chains cotton white luxury Italy L Boutique Moschino Button Down Sweater Pink 38 BOUTIQUE MOSCHINO PUSSY BOW BLOUSE TOP PINK SIZE 42 NEW WITH TAGS I LOVE LOVE BY MOSCHINO EDT SPRAY 1.0 OZ (WOMEN) NEW IN BOX Boutique Moschino 100% Silk Dress U.K 12 bnwt RARE LOVE MOSCHINO COUTURE CREW NECK SHORT SLEEVE COTTON WHITE DRESS SIZE 4 nwt Moschino MOS130/S 807 BLACK 55/20/140 WOMAN Sunglasses RRP 365$ BNWT Moschino Mare Blue Shirt 52 / L MOSCHINO HEART SHIRT BLOUSE WOMEN’S size 14 Moschino Cheap and Chic Size 8 Strapless Dress Black Cotton Chiffon Overlay Hot! Moschino Toy 2 3pc Set Women Parfum Spy 1.7 oz + Shower Gel + Body Lotion 50% SALE DESIGNER PERFUMES 10 /$19.95 DG M JACOBS MOSCHINO CARTIER+BAG Moschino Jeans Black Tiered Skirt Womens 8 Skirt Belted Short Zipper Moschino Couture Jeremy Scott all over teddy bear policeman pink knit dress US10 Moschino Green Open Toe Floral Detail Shoes Women’s Size 36 1/2 US 5.5 New With Tags Moschino Arm Tape Logo Light Blue Sweatshirt US M (Retail 185$) Mens Pullover Fleece Hoodie