$414.76 Buy It Now or Best Offer
free,30-Day Returns
Seller Store
() %,
Location: Ontario, California, United States
Ships to: US,
Item: 266487955039
eBay 1.Fitting the Following vehicle: 2002-2006 Cadillac Escalade 2002-2006 Chevrolet Avalanche 1500 1999-2006 Chevrolet Silverado 1500 2007 Chevrolet Silverado 1500 Classic 2000-2006 Chevrolet Suburban 1500 2000-2006 Chevrolet Tahoe 1999-2006 GMC Sierra 1500 2007 GMC Sierra 1500 Classic 2000-2006 GMC Yukon 2000-2006 GMC Yukon XL 1500 2.Package Includes: 14x Front Control Arm And Ball Joint Wheel Hub Bearing For 99-06 GMC Sierra 1500 1.Fitting the Following vehicle: 2002-2006 Cadillac Escalade 2002-2006 Chevrolet Avalanche 1500 1999-2006 Chevrolet Silverado 1500 2007 Chevrolet Silverado 1500 Classic 2000-2006 Chevrolet Suburban 1500 2000-2006 Chevrolet Tahoe 1999-2006 GMC Sierra 1500 2007 GMC Sierra 1500 Classic 2000-2006 GMC Yukon 2000-2006 GMC Yukon XL 1500 2.Package Includes: 2x Wheel Hub Bearing -515071 4x Ceramic Brake Pads -D785-7653 2x Front Inner Tie Rod End -ES3488 2x Front Sway Bar End Link -K80631 2x Front Outer Tie Rod End -ES3493T 2x Front Upper Control Arm And Ball Joint -K80942 1x Front Lower Control Arm And Ball Joint – Passenger Side -K620380 1x Front Lower Control Arm And Ball Joint – Driver Side -K620381 2x Brake Rotors -55054 ” 3.Note (1).Please check the Compatible Fitment Chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. 10 Year Warranty This item is backed by our 10-year warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only. Please note: Any modifications to an item of any kind before contacting us will void any and all warranty coverage for this item. Please contact us before modifying the part so that we have the opportunity to correct the situation. ” Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Included Hardware : Mounting Hardware Custom Bundle : Yes Interchange Part Number : 515071 D785-7653 ES3488 K80631 ES3493T Superseded Part Number : K80942 K620380 K620381 55054 OE/OEM Part Number : Suspension Control Arms and Steering Tie Rod Ends Linkages Manufacturer Warranty : 10 Year Brand : topcn-autoparts Manufacturer Part Number : TA83732101P Adjustable : Yes Material : Alloy Steel Kit or Single Part : Kit Surface Finish : Polished, Rust Protected Quantity : 14Pcs Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On Finish : Coated Rotor Style : Drilled & Slotted Rotors Finish : Zinc Plated Pads Material : Ceramic Features : Greasable Discount Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales 2 For Dodge Challenger 2008-2014 Keyless Entry Remote Control Car Key Fob USD 19.43 2x Front Hood Lift Supports Shocks Struts For Dodge Ram 1500 2500 3500 4500 5500 USD 19.49 2x Front Hood Gas Lift Supports Struts Shocks Springs For Dodge Ram 02-10 4364 USD 17.69 2x Rear Trunk Hatch Liftgate Lift Supports Springs Struts For Scion tC 2005-2010 USD 16.49 Upstream & Downstream Oxygen O2 02 Sensor For 2001-2005 Honda Civic 1.7L D17A7 USD 26.45 Newly Listed Headlights Assembly Pair For Nissan for Altima 2013-2015 Chrome Housing USD 130.99 Fits 2007-2015 Toyota FJ Cruiser Headlights + Tail Lights Lamp With Grille USD 510.29 2pcs for 98-2002 Mitsubishi Mirage 1.8L Upstream Downstream 02 O2 Oxygen Sensor USD 25.99 Upstream Front Oxygen O2 Sensor 02 for Dodge Dakota Durango 2001-2002 4.7L USD 16.99 Black Side Mirrors For 15-18 Silverado Sierra 1500 Power Heated Signal Puddle USD 138.99 Terms & Contact Shipping Policy Payment Policy Return Policy FAQ About Us 14x Front Control Arm And Ball Joint Wheel Hub Bearing For 99-06 GMC Sierra 1500 1.Fitting the Following vehicle: 2002-2006 Cadillac Escalade 2002-2006 Chevrolet Avalanche 1500 1999-2006 Chevrolet Silverado 1500 2007 Chevrolet Silverado 1500 Classic 2000-2006 Chevrolet Suburban 1500 2000-2006 Chevrolet Tahoe 1999-2006 GMC Sierra 1500 2007 GMC Sierra 1500 Classic 2000-2006 GMC Yukon 2000-2006 GMC Yukon XL 1500 2.Package Includes: 2x Wheel Hub Bearing -515071 4x Ceramic Brake Pads -D785-7653 2x Front Inner Tie Rod End -ES3488 2x Front Sway Bar End Link -K80631 2x Front Outer Tie Rod End -ES3493T 2x Front Upper Control Arm And Ball Joint -K80942 1x Front Lower Control Arm And Ball Joint – Passenger Side -K620380 1x Front Lower Control Arm And Ball Joint – Driver Side -K620381 2x Brake Rotors -55054 ” 3.Note (1).Please check the Compatible Fitment Chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. 10 Year Warranty This item is backed by our 10-year warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only. Please note: Any modifications to an item of any kind before contacting us will void any and all warranty coverage for this item. Please contact us before modifying the part so that we have the opportunity to correct the situation. ” Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Included Hardware : Mounting Hardware Custom Bundle : Yes Interchange Part Number : 515071 D785-7653 ES3488 K80631 ES3493T Superseded Part Number : K80942 K620380 K620381 55054 OE/OEM Part Number : Suspension Control Arms and Steering Tie Rod Ends Linkages Manufacturer Warranty : 10 Year Brand : topcn-autoparts Manufacturer Part Number : TA83732101P Adjustable : Yes Material : Alloy Steel Kit or Single Part : Kit Surface Finish : Polished, Rust Protected Quantity : 14Pcs Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On Finish : Coated Rotor Style : Drilled & Slotted Rotors Finish : Zinc Plated Pads Material : Ceramic Features : Greasable DiscountShippingWarrantyReturnFeedback Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of Topcn-autoparts. All rights reserved.
Frequently Asked Questions About 14x Front Control Arm And Ball Joint Wheel Hub Bearing For 99-06 GMC Sierra 1500 in My Website
swidnw.com is the best online shopping platform where you can buy 14x Front Control Arm And Ball Joint Wheel Hub Bearing For 99-06 GMC Sierra 1500 from renowned brand(s). swidnw.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling 14x Front Control Arm And Ball Joint Wheel Hub Bearing For 99-06 GMC Sierra 1500 on swidnw.com?
swidnw.com helps you to shop online and delivers Moschino to your doorstep. The best-selling Moschino on swidnw.com are: Moschino MOS020/S Womens Large Metal Sunglass DDB3X Gold Copper w Pink 59-16 Love Moschino Purse Borsa Vit Black Genuine Leather Gold Studded Shoulder Bag Moschino Brown Faux Pearl Eyeglasses *FRAMES ONLY* MO084-04 53-16-135 Italy NWOT Moschino Classic Body Powder With Puff New Moschino Women’s 8 Off White Linen Blend Relaxed Pants MOSCHINO COUTURE! Black Classic Shift Dress – Gold Grommets USA 8 GB 10 Moschino by Moschino, 2.5 oz EDT Spray for Women Women’s Moschino Black Tapered Leg Jersey Knit Pants Size 10 Moschino White X Kelloggs Tony The Tiger Graphic Sweatshirt LOVE MOSCHINO Womens Dress Size 46 Size 10 Python Heart Print Logo Long Sleeve Moschino Cheap And Chic Tweed Style 100% Wool Blazer Jacket UK Size 10 Moschino Cheap & Chic Dress Mixed Print Silk Twill Size US 4 Twist-Front Sheath Moschino Cheap & Chic Black Jacket Size 46 IT Moschino Boutique Tweed Jacket Pink Cropped Pearl Buttons Long Sleeves Size 10 M VINTAGE MOSCHINO RARE ESTATE SALE FIND BLACK CAMEO PATCH PULL ON HI LO SKIRT S/M AW20 Moschino Couture Jeremy Scott Shipping Boxes Packaging Materials Overcoat MOSCHINO LEATHER SKIRT Moschino Jeans Women’s Linen Blazer Size 6 Navy Blue Dark Academia Boutique Moschino stretch High Gather Waist skirt Size IT40 USA6 F36 8 Moschino Cheap Chic Eyelet Wiggle Dress White Cotton Italy Boutique Moschino! -Print Ribbon Dress Size 6US -Very chic! Original Price $525 China Airlines x Moschino Business Class Deluxe Travel Amenity Kit French Blue Moschino Cheap And Chick NWT Dress IT 46 Abstract Print Dolman Sleeve Belted BOUTIQUE MOSCHINO Dress Women Sz 6 RARE Designer Branded Signature Novelty Print Moschino Couture Logo Budweiser printed cotton-jersey joggers pants SZ 10 read Moschino MOS508 C9A 53 Women Eyeglasses Moschino Jeans Women Medium IT 42 Jacket Floral Black Button Long Sleeve Moschino Boutique black jacket coat Sz 6 MOSCHINO FOREVER SAILING FOR MEN EDT SPLASH 20×4.5 ML. MINIATURE (PACK OF 20) MOSCHINO Sunglasses (original Retail Price Was $270.00) MOSCHINO BLACK GRAPHIC PRINT LEATHER CLUTCH RETAIL MADE IN ITALY BNWT MOSCHINO Milano Second Bag Pouch Denim Blue Authentic Used Very Good Item Japan Moschino “I Love 70” Watch New Toy 2 Bubble Gum by 3.4 oz EDT for Women Perfume in Box Moschino This Is Not A Moschino Toy Retro Vintage T-Shirt, S-5XL Moschino Pink Signature Tee T-shirt Rare NEW Moschino Vintage Pebbled Leather Lock Travel Handbag Ivory color Rare 90’s Moschino Dress Apricot Sleeveless Fit Flare Bow Hips Sweetheart Neck Cotton 8 Moschino Lettering Logo Calfskin Women’s Belt in Black with Gold Hardware IT 46 Moschino Women’s 189350 One-Piece Patchwork Animal Print Swimsuit Size 1 Love Moschino Dress Womens 4 Black Sweater Dress Long Sleeves Casual Vintage 80’s Franco Moschino Cheap&Chic RARE Happy Things Shirt 16.5 Men NWOT Moschino Couture by Moschino for Women 1.7 oz Deodorant Parfume Natural Spray L’eau Cheap & Chic by Moschino Eau De Toilette Spray 1.7 oz — Love Moschino Black Yellow Dress Club wear Women’s Dress Size US 2 EU 38 NEW Grey Love Moschino Vest Tank Top With Embroidered Print Size GB 10 Moschino Cheap & Chic Wool Beaded Butterfly Collared Sweater Black Sz 8 vintage cheap and chic Moschino Dress Size 6. MOSCHINO x Disney Top Womens Extra Small Short Sleeve Yellow Tee H&M MOSCHINO Moschino 8-Bit ‘This is not a Moschino Toy’ Bear Logo Tee NEW MOSCHINO MOS128/S MVUIR BLUE AUTHENTIC SUNGLASSES W/CASE 57-14 Love Moschino New Solid Red Sheath Sleeveless Fitted Dress 8 NWOT H&MOSCHINO MOSCHINO H&M JACKET PARKA COAT GOLD SIZE XS Moschino baby girl pink cotton teddy bear logo sweatshirt size 12-18 months, 3 Vintage Moschino Cheap Chic Green Large Bow Shift Mini Dress Sz 8 NEW LOVE MOSCHINO BLACK COTTON LOVE & PEACE EMBROIDERY BLOUSE TOP SHIRT,UK 14 MOSCHINO Jeans Vintage Italy Black/White Check Wool Oversized Shirt Size S Vintage 90s y2k Moschino Mare Dress Slinky Embellished US Size 34 Medium MOSCHINO COUTURE Moschino Couture T-shirt Black ZPA0701 Love Moschino Brown Short Sleeve Shirt size L Cheap and Chic Classic by Moschino Eau De Toilette Spray 1.7oz Love Moschino Men’s Airline Logo Short Sleeve T-Shirt NWT Y2K 2000s Love Moschino Pink Silk Lady Bug Mini Dress drop waist ruffles US 8 LOVE MOSCHINO BASEBALL BLACK PANTS STYLE sz IT 42 US 6 NEW RETAIL $354 MOSCHINO CHEAP AND CHIC BOUCLE DRESS 6 CORAL PINK GOLD BUTTONS BOW FRAN FINE Love Moschino Green Ruffle Draped Long Sleeve Shift Dress Size 10 Love Moschino Womens Sequined Tee Shirt Team Moschino Size 6 NWT MOSCHINO WOMEN’S T SHIRT Yellow Flicker Pink Camouflage Logo (U-002) Moschino Cheap & Chic Vintage Mesh Lavender Embroidered Cami Top | IT 44 | UK 12 MOSCHINO COUTURE BLUE JACKET Trompe L’oeil Blazer USA 4 IT38 $2.4K 2021 RUNWAY Vtg Moschino Jeans Mini Dress Cotton Halter Floral Bow Side Zip Black Small Moschino Olive Oyl Silk Scarf Orchard Heart Cottage Designer Italy Vtg MOSCHINO CHEAP & CHIC 90s DA VINCI OLIVE OYL PRINT BLACK DRESS 42 M Moschino Couture Silk Multicolor Watercolor Abstract Floral Peplum Blazer 42 M Moschino Vintage Faux Leather Jacket PVC Blazer Womens US 8 / It 42 MOSCHINO LOVE DRESS SIZE 10 U.K. RARE Love Moschino Love Logo T-Shirt Black Retro Rainbow HTF Size 8 EUC NWT*MOSCHINO Jeans* shirt-blouse*Size 40 (IT)*RED WINE color*Crystals*VINTAGE Moschino Cheap and Chic Sexy White Draped T Shirt 44/10 Moschino H&M DISNEY Daisy Donald Duck Jumper Sweater Dress S MOSCHINO Women’s Beige Tulip Skirt Asymmetric Pencil Skirt Size 8 / 44 / L MOSCHINO Black Calendar Silk Tie ITALY 56”/ 3.5” EC MOSCHINO mens Shirt Vintage 90s All Over Print Made In Italy 2018 MOSCHINO x H&M Hot Pink Disney Minnie Mouse Merino Wool Sweater Dress – S NWT MOSCHINO HOODIE SWEATSHIRT Teddy bears chains cotton white luxury Italy L Boutique Moschino Button Down Sweater Pink 38 BOUTIQUE MOSCHINO PUSSY BOW BLOUSE TOP PINK SIZE 42 NEW WITH TAGS I LOVE LOVE BY MOSCHINO EDT SPRAY 1.0 OZ (WOMEN) NEW IN BOX Boutique Moschino 100% Silk Dress U.K 12 bnwt RARE LOVE MOSCHINO COUTURE CREW NECK SHORT SLEEVE COTTON WHITE DRESS SIZE 4 nwt Moschino MOS130/S 807 BLACK 55/20/140 WOMAN Sunglasses RRP 365$ BNWT Moschino Mare Blue Shirt 52 / L MOSCHINO HEART SHIRT BLOUSE WOMEN’S size 14 Moschino Cheap and Chic Size 8 Strapless Dress Black Cotton Chiffon Overlay Hot! Moschino Toy 2 3pc Set Women Parfum Spy 1.7 oz + Shower Gel + Body Lotion 50% SALE DESIGNER PERFUMES 10 /$19.95 DG M JACOBS MOSCHINO CARTIER+BAG Moschino Jeans Black Tiered Skirt Womens 8 Skirt Belted Short Zipper Moschino Couture Jeremy Scott all over teddy bear policeman pink knit dress US10 Moschino Green Open Toe Floral Detail Shoes Women’s Size 36 1/2 US 5.5 New With Tags Moschino Arm Tape Logo Light Blue Sweatshirt US M (Retail 185$) Mens Pullover Fleece Hoodie